Trusted design professionals since 1995
What’s Covered on This Page
- Section 1
- Oil & Gas Facility Modeling Covers Full Calgary Sites
- Tank & Vessel Modeling Captures Single Storage Assets
- Skid & Pump Package Modeling Supports Fabrication Yards
- Compressor/Gen-Set Modeling Documents Rotating Equipment
- Which modeling service do I need for my facility or asset?
- Do you cover sites outside Calgary, across Alberta?
- How does industrial design work in Calgary’s fabrication yards?
- What’s the difference between facility modeling and tank or vessel modeling?
- Do your models meet AER and CSA/API documentation requirements?
- How do I decide between skid modeling and compressor or gen-set modeling?
Section 1
Industrial design company services in Calgary look different once you factor in the energy sector. Near downtown and the 6th Ave SW corridor, operators and engineering firms manage sites and equipment scattered across Alberta, and they need 3D models built from real field data, not guesswork. Masters-3D is an industrial design company in Calgary covering four modeling services: full facility modeling, tank and vessel modeling, skid and pump package modeling, and compressor/gen-set modeling. This page gives you a quick look at each one so you can figure out which fits your project, then click through to the full service page for process details and scope questions. Our team consists of licensed engineers with project history in oil & gas, industrial, and structural work dating back to at least 2020. That background shapes how we approach every model – accuracy first, documentation second, prefabrication third. The thesis is simple: we match Calgary operators and fabricators with the right modeling service for their facility, asset, or equipment package.
Contact Masters-3D to talk through your facility or equipment modeling project.
Oil & Gas Facility Modeling Covers Full Calgary Sites
Oil & Gas Facility Modeling is the service to reach for when you need one model that covers an entire site – piping, structures, and multiple assets together, not a single piece of equipment. Downtown Calgary operators near 6th Ave SW often manage remote sites across Alberta, and an accurate facility model supports AER and CSA/API documentation requirements without a site visit for every review. We build these models from scan data and validated engineering, then deliver them in formats that fit your existing workflow – point cloud, E57, RCP, or DWG, depending on what your team needs downstream.
Honestly, this is the step people underestimate. A facility model isn’t just a picture of what’s there. It’s the base layer for future design work, turnaround planning, and P&IDs, as-builts, and plot plans that follow. Unlike Tank & Vessel Modeling, this service covers an entire site rather than one piece of equipment. If you’re scoping a full turnaround or need as-built documentation across a lease site, this is the entry point. Oil & Gas Facility Modeling in Calgary
Tank & Vessel Modeling Captures Single Storage Assets
Say you’re planning a retrofit, inspection, or fabrication task tied to one storage or process vessel. That’s Tank & Vessel Modeling. It’s a focused model of a single tank or vessel, sized and detailed for the exact task in front of you, without the scope – or cost – of a full facility project.
We scan the asset, then build a stamped, validated model our licensed engineers can stand behind. Deliverables typically include:
- Point cloud and E57 scan data for reference
- STEP or IGES files for design integration
- DWG drawings for site documentation
- Dimensional accuracy checked against field conditions
Unlike Oil & Gas Facility Modeling, this service targets one asset instead of an entire site. If your project is a single tank ahead of an inspection window, this is a tighter, faster fit. Tank & Vessel Modeling in Calgary
Thinking about Industrial design company? Let’s talk.
Call now. Masters-3D is ready to help.
Skid & Pump Package Modeling Supports Fabrication Yards
What does a fabrication yard actually need before a pump skid ships? A model built around the real geometry – not the drawing that was supposed to match it. Skid & Pump Package Modeling supports fit-up, integration, and documentation before equipment leaves the shop.
Calgary’s industrial parks, including Foothills, Great Plains, and Shepard, host fabrication yards where skid packages get built and staged before shipping. We scan the skid or pump assembly, cross-check it against design intent, and produce 3D piping and structural steel drawings that reduce rework once the package is on site. That rework reduction is the whole point – a model that matches reality saves cost on the install end.
Unlike Compressor/Gen-Set Modeling, this service focuses on fluid-handling and pumping systems, not rotating gas or power equipment. If your scope is pump skids or aggregate handling trailers headed for a fabrication yard, this is the service. Skid & Pump Package Modeling in Calgary
See the full Oil & Gas Facility Modeling page for scope details and project examples.
Watch Our Video
See How We Handle Industrial design company in
Masters-3D
Compressor/Gen-Set Modeling Documents Rotating Equipment
Compressor/Gen-Set Modeling is for buyers already specified on a compressor or generator package who need a model tied to that exact equipment class. This isn’t fluid-handling work – it’s rotating equipment for gas compression or power generation, and it carries its own documentation standards.
We build these models to match the equipment as it actually sits, then validate the output against engineering drawings our licensed team stamps and signs off on. That stamped accuracy matters when the model feeds into oil battery design or civil grading plans downstream – errors compound fast if the base geometry is off.
Unlike Skid & Pump Package Modeling, this service covers rotating equipment for gas compression or power generation rather than fluid-handling systems. Reach out to Masters-3D’s Calgary office to scope your next modeling project. We offer a free estimate – email [email protected] or call 587-323-3900.
Frequently Asked Questions
Common questions about Industrial design company
Which modeling service do I need for my facility or asset?
It depends on how much you’re covering. If you need a model of an entire site with piping and structures, choose Oil & Gas Facility Modeling. If you’re focused on one tank, pick Tank & Vessel Modeling. Pump systems point to Skid & Pump Package Modeling, and rotating gas or power equipment points to Compressor/Gen-Set Modeling. Not sure? Call us and we’ll match you to the right one.
Do you cover sites outside Calgary, across Alberta?
Yes, we work with Calgary operators who manage remote sites across Alberta. Many of our clients are based near downtown and the 6th Ave SW corridor but need modeling done at lease sites hours away. We build the model from real field scan data, so your team gets accurate documentation without a site visit for every review.
How does industrial design work in Calgary’s fabrication yards?
Skid & Pump Package Modeling is built for this. Calgary’s industrial parks, including Foothills, Great Plains, and Shepard, host fabrication yards where skid packages get staged before shipping. We scan the assembly and cross-check it against design intent, so the model matches what’s in the yard, not just the original drawing.
What’s the difference between facility modeling and tank or vessel modeling?
Facility modeling covers an entire site, piping, structures, and multiple assets together. Tank & vessel modeling covers just one storage or process asset. If you’re planning a full turnaround or need as-built documentation across a lease site, facility modeling fits. If your project is one tank ahead of an inspection window, tank & vessel modeling is the tighter, faster choice.
Do your models meet AER and CSA/API documentation requirements?
Yes, our facility models support AER and CSA/API documentation without requiring a site visit for every review. We build them from scan data and validated engineering, then deliver in formats like point cloud, E57, RCP, or DWG. Our licensed engineers validate the output so the model holds up when it feeds turnaround planning or as-built records.
How do I decide between skid modeling and compressor or gen-set modeling?
It comes down to what the equipment does. Skid & Pump Package Modeling covers fluid-handling and pumping systems. Compressor/Gen-Set Modeling covers rotating equipment for gas compression or power generation. If you’re already specified on a compressor or generator package, that’s the service you want. If it’s pumps or fluid handling, go with skid modeling instead.
Recent Comments